Error 5101 phoneview3/14/2023 You have 6 endstop pins and need 3 forĮndstops + 1 for zprobe = 4 pins. I guess you missed the pullup part making it a random result.Īnd Is there a complete step by step manual for building Z probe - Comment_1952 Then set it in zprobe section with pullup enabled so it is drawn to high internally until you connect the pin with gnd. Put the zprobe on any free pin you have but do NOT set it in endstops. See Is there a complete step by step manual for building Z probe - comment 1950 Obviously, you will leave the three #defines for the MIN end stop, in Configuration.h, un-configured, and then specify the pin, that you did use, in So, you can simply connect the Z-probe to any of the three MIN end stop pins, on the board. Now, you probably only have three end stops, at the top of the delta frame. If your Z-probe has become unplugged, then you need to choose a pin to connect it to. For example, if it is connected to pin 63, then:Īnd leave DISTORTION_CORRECTION untouched. If you do have a Z-probe, then trace the wires to see where they go on the controller board, determine that pin number on the board and then enter that pin number into configuration.h. NOTE: It might be easier to just define Z_PROBE_PIN to something other than -1, which is what it is defaulting to, as set in configuration.h: In that case check board description and use the digital pin number instead for that function. You are using ORIG_FAN2_PIN in your configuration but apparently your boards pin definition does not define that pin. This error:įastio.h:29: error: 'DIOORIG_FAN2_PIN_WPORT' was not declared in this scope but these seem to be more to do with selecting the correct board, #define MOTHERBOARD, in pins.h, than the disabling of the Z-probe. However, thereafter, upon recompilation, I then get a lot of other errors. If not, then in configuration.h set the FEATURE_Z_PROBE to false, like this:Īs this requires the FEATURE_Z_PROBE if otherwise set to 1 or true. "You, obviously, do actually have a Z-probe, but in case another user does not, or you decide not to use yours, I will cover both cases (with and without a Z-probe). Also, there is a T0 on the additional board which is connected to A13 of the main controller." The X-min and Z-min are connected to the X-min and Z-min on the additional green board respectively. Hope this helps.Įdit2: The Y-min pin on the main controller board is empty. Please note that this is v1.1 and my printer has v1.3 although I haven't found any difference between the two, yet. On the web these printers are known as "D-force printers".Įdit1: I found this on the manufacturer's Facebook group: Here is a close-up of the Z-probe & the servo motor that pins it down.Īny help would be appreciated here. I'm unable to do so because it's not plugged into the main board. Now, while compiling the firmware, I need to specify the Z-probe pin. It can be found here, Repetier-Firmware. I've downloaded a new firmware from Repetier website. I haven't been able to find the other green board (with the HRD12008 SMPS on it), yet. I've traced the printer down to a Taiwanese manufacturer: D-FORCE.TW - 3D Printer. The brand on all these boards is "D-force". The other box with an acrylic top is a solid state relay. The other green board beside it has a DC to DC SMPS (HRD12008) on it, along with Z-min, X-min, T0, Fan-, D11 and a flat ribbon wire connector (can be seen in the picture). These are the controller boards of my printer: "Building new Repetier firmware for a delta printer (D-force) So my printer's calibration got screwed after a sudden reboot and since the current firmware (0.92.6) is licensed, I cannot edit it.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |